There were two of them, Australian Emblem and Australian Escort. They ran between Australia and Japan. I went aboard the Emblem in Brisbane for instruction on AWA paperwork when I first came to Australia and the Escort for a Christmas Day booze up in Melbourne. Nice ships but, sorry, no info on the engine room.

Is Chillitoes still around on the site. He was an engineer with ANL and should be able to help you.

John T

 

Emblem and Escort were considered second generation RoRo

The first generation were the Australian Enterprise and Explorer, and also had the three engine Kawasaki MAN V16 42/47 (?), whereas the Emblem/Escort were 52/55. Configuration to keep deckhead low for stern ramp etc. was #1 and #2 bottom plates, into gear box aft, with #3 above the main shaft coupled to gear box in the front end. Escort and Emblem were much more sophisticated than the first generation, and cleaner to work on. The Enterprise, which I spent years on, had two turbocharges at each end of the engine and as they were pulse, it meant 4 units were manifolded to each T/C. There were two fuel lines to each unit because in port one main engine still fed the gear box, which provided electrical load so under lighter load lower fuel volumes needed. The alternators (2 off) came off the back of the gear box, aft and basically under #3 . No such thing as an auxiliary , only a sooped up truck engine to get initial power on to get a main back on. They were dirty and hard working ships, crap cheap fuel, low loadings (under blown) in port burnt exhaust valves out continually, and sulphured up the inlets so badly you would break cages getting the valves out. One trick was to loosen all cage bolts on the set of units to change before shutting down, then manually pushing the individual fuel racks in to increase peak pressure to bounce the cage. Of course a lot of smoke, noise, and trepidation releasing nuts a turn while the 4 valve handshake rocker gear tried to gobble your hands. ANL also did the cheap by only having 1 exhaust probe per 2 exhaust pockets, so it was common for newbies to pull the wrong exhaust valve, as pulse from coupled manifold could cause a wrong interpretation. Old hands used to turn the ER lights off on night rounds, then walk along the heads looking for cherry red exhaust pocket manifolds to pick the valve. Then off course reducing CPP, de-clutching the horrible air bag clutch, stripping rocker gear, and changing the offending valve, all on your lonesome, then of course getting everything back on line and baby sitting back to full biscuit. A 24 hour gear turn every 4 days, rarely meant any sleep, or if with a newbie to back up, no sleep every 2 days.Could go on about the crap design of water cooling exhaust valves which continually filled the rocker gear with water leaks (220 face to face connections), plus fuel leaks (96 connections), and non functioning ball and slide exhaust valve rotators, but hell I would need to write a book.
The 3rd. generation for ANL was the ANRO Australia, MAN 9L 52/55 with one exhaust manifold (constant pressure), one T/C, horse collar exhaust manifolds to units, fin exhaust rotators, only 2 engines into gear box, with alternators on free ends facing forward. Eventually the engines were under powered, as more refer points were added (initially 100, then to just over 300), and with 24 gear turn on ER, and 24 hour on Reefers, then day work (3 Engineers), it was a different hell. Guess with an economiser, and an silencer, also enclosed within the two decks, and running Singapore, Kelang, Penang and round Aussie, there would have been no ER hotter anywhere, besides the hotter the ER the more efficient the plant (not that anyone ever acknowledged the basic thermodynamic logic vs human).
At the end of it all 3 generations produced medium speed engineers that could solve anything, from the rough and unique, to a bit of finesse.
Damn hard years, and I look back and think how did we do it. A lot of young keen engineers as cannon fodder, but with duty free kegs, who could argue.

 

The first generation were the Australian Enterprise and Explorer, and also had the three engine Kawasaki MAN V16 42/47 (?), whereas the Emblem/Escort were 52/55...........................................................................................
Damn hard years, and I look back and think how did we do it. A lot of young keen engineers as cannon fodder, but with duty free kegs, who could argue.

Anyone remember the PAD Line trio with three V18 Pielstick 2.2 trying to burn Bass Strait fuel and those 5 lovely air clutches? Methinks they were the prototype for the ones you are talking about (Cloud)

 

As an electrical chappie, fresh from the shooting navy, I was invited (pressganged) to join "Roy's Navy" in early 1976. Served 4 years on the Enterprise with occasional relievers on the Explorer, Escort and Anro and I can only applaud DaveU's succinct and elegiac summation of the vessels in question. The Enterprise and explorer, being first generation, were particularly demanding and the reason why Roy MacDonald was reputed to choose his own engineering teams. I well remember crawling around the darkened pit looking for glowing exhaust manifolds.
Took her to Kobe in 1978 where she was cut in half and lengthened by 29 metres increasing her capacity by 375 TEU.
On a more personal note: riding a wave of nostalgia, brought on by these postings, I retrieved my old ANL "Studbooks" and found a certain Dave U. on the Australian Exporter, in mid 1987, among other mentions.
Cheers mate. They were exciting years.

 

DaveU, Bally heck! So glad I did most of my short three years on steam turbines (Thumb)

 

Can’t wholly agree with Bas, on account steam leak experience.
But that job you were on surely not sound a barrel of laughs Dave!! (&bp2002/Olaf)

 

Thank you! Dave and Olaf. What a great response!
The other side of the picture: not quite what owners and builders like to show the world!
Btw, was bridge control of the propulsion plant usual?

 

My pleasure Blueprint.
As per your original post Australian shipping was in the vanguard of shipping innovation in the early days. ANL being one of the first to adopt containerization and to extend RoRo shipping into international liner trades. This allowed greater versatility in the type of cargo shipped and faster turn-around as forklifts could work the vehicle decks while cranes worked the uppers.
The vessels were UMS so CPP control was switched from control room to bridge as required. The engines were governed to a constant 400 rpm as they also drove the alternators.

 

Thanks again, Olaf. I imagine engines were connected or disconnected depending on the need (such as deep draft, manoeuvring etc): this might be from the control room?

 

Thanks for blowing my cover, John!

In fact, I only did two swings on Australian Emblem, not ever being part of Roy's Navy (ex-ANL people will understand this). I cannot remember any great engineering dramas of the kind outlined here by others, and I can only remember maybe 3 serious incidents during my whole 22 years at sea. What a boring life!

As DaveU has said, Aus. Emblem (1975) and Aus. Enterprise (1969) were built for ANL and their sisters, Matthew Flinders and James Cook were built for Flinders Shipping Co. Both these latter vessels were acquired by ANL in 1975, Matthew Flinders became Australian Explorer and James Cook became Australian Escort. Enterprise & Explorer were lengthened in 1978, going from 596 to 690ft.

I have attached a couple of scans, showing colour image and ship details from stuff in my collection. The Mitsubishi do***ent also has a fold-out of the GA. but it is A3, too big for my scanner.

While on the subject of ANL, I can never understand why there doesn't seem to have ever been a re-union of former staff - did we hate each other that much? There was a couple of years ago a re-union of former engineering cadets, but that's it. Anybody got any contrary info?

 

………..

I have attached a couple of scans, showing colour image and ship details from stuff in my collection. The Mitsubishi do***ent also has a fold-out of the GA. but it is A3, too big for my scanner.
……..

Thanks for the scans, Chillytoes. Hard to find anything like that, so many years later.

 

Olaf the Blue
This is a 1986 pic of the remains of Dilkara (or maybe perhaps Allunga) taken from the after deck of Cape Hawke, which was soon to suffer the same fate.

 

Blueprint noted the innovation that was once part of the now vanished Australian shipping scene. Just a couple of those innovations: MV Kooringa - the first ‘purpse-built’ container ship. OK, it was designed for non-standard containers, but none the less, it was built with cell guides, the first to be done so. As an apprentice, I worked on her construction.
Then there were the 7 gas turbine powered vessels built at Whyalla. I sailed on two of them. Sadly, the fuel price skyrocketed resulting in them becoming uneconomical. A couple were re-powered and soldiered on for a few more years. Then there was the hatchless ships, which sadly did not work out.
There were wins and losses, but all of it now gone. So sad, especially for an island nation!

 

And I believe there were two separate classes of coal-fired steam bulk carriers in the 70s and 80s, so as to use the coal which was anyway available at one of their terminal ports. One of them was ANL, was BHP the other?

 

The ANL ships, River Boyne (1982) and River Emberley (1983) were built by Mitsubishi-Nagasaki. The TNT vessels, Carpentaria & Capricornia, were both built by Italcantieri-Monfalcone in 1983. In 1994 both these vessels changed names, Capricornia became Fitzroy River and Carpentaria became Endeavour River. They remained in the same ownership, which also changed its name.

 

Was the Bogong one of that class?

 

No, Andy. Bogong was built in 1967 for Bulkships. In 1977 it was taken over by BHP and renamed Iron Bogong. I believe she was a motor vessel, (Doxford, I think) although one source lists her as 'hot fog'. She went to Kaohsiung in 4/83.

Oops! Bogong was GE steam turbine, along with sister ships Iron Hunter, Darling River and Yarra River. Sailed on Yarra River.

Since this thread started with Australian Emblem, here's a picture of her control room. Looks much cleaner and neater than I remember.

 

Prior to being taken over by BHP, Bogong was managed by ASP. Some of the ASP staff were also transferred to BHP and it wasn't a popular move with BHP staff because it up0set promotion prospects. Former ASP staff became known as "Snake Men" and some of them complained. A circular was sent around the fleet telling staff to desist from using the name.

Funny thing about TNT Carpentaria and Capricornia - they had pool tables in the smoke room! During the passage through the Barrier Reef it was so calm and with no vibration it was possible to play.

John T

 

My mistake, when I look at the dates it all made sense, I remember a group of us from the Baron Pentland ending up on the Bogong for drinks (that's why the memory was hazy)

 

DaveU. Long time no hear or speak. You may remember me when we were on the Enterprise in Incheon on a very cold winter night. Along with a couple of others we managed to find our way onto a Korean warship only to be arrested and detained. My recollection is that your smooth talking over some 6 or so hours saw us ending up friends with the crew of the warship.
On another occasion we were sailing together on the Emblem with the 3rd engine dismantled when we blew a turbo on #1. You and I worked some 2+ days straight to replace the nozzle ring that had to be dropped off from the Escort.
Those were the good times weren’t they